China manufacturer Low cost Manual lifting screw jacks with hand wheel near me supplier

Low cost Manual lifting screw jacks with hand wheel

Manual screw jack introduction

Manual Screw Jack is composed of hand wheel or hand crank and a worm gear screw jack, which has intermittent precisely positioning and self-locking feature for no creeping down without brake mechanism or other locking systems, when manual ball screw jack, no self-locking feature, avoid ball screw back drive with attached load, which needs additional brake mechanism or other locking system to prevent it creep.

Manual Screw Jack is ideal solutions for applications where electricity or power generators is inconvenient or dangerous, light weight, low duty cycle, low target cost and short travel length.

Main features:
1. Suitable for heavy load, low speed and low frequency;
2. Main components: precision trapezoid screw pair and high precision worm gear pair; for GMC Sierra Yukon CZPT K1500 Pickup K2500 K3500 Over 200 Items Front Rear Drive Propeller Shaft Driveshaft
3. It has self-locking function and can hold up load without braking device.
4. Top End: top plate, clevis end, threaded end, plain end
5. Widely applied in industries such as machinery, metallurgy, construction and hydraulic equipment.
6. Enjoy many functions such as lifting, pushing and turning.
7. Enjoy features of compact structure, small volume, light weight, wide drive sources, low noise, Tungsten Carbide Drilling Bushes Drill Bushing Sleeves high reliability and long service life.
8. Easy to be mounted, flexible in use.
9. Accurately control the height of lifting or pushing.

How to Choose a Screw Jack? Some questions you need answer pls.
Q1: The capacity is to load ? KG (it means how many Kg or Tons the screw jack need to lift or drop?)
The stroke is ? mm (it means the screw shaft length, such as 500mm)
The lifting speed is ? mm/second (it means how much time you want to use to finish the stroke? Such as I want to use 20 seconds to finish the 500mm stroke then can come out the speed is 25mm/s )
Screw jack SWL2.5-120 performance parameters table as the below:

Q2: Which the screw top you need? Answer: I need (T H S R).

Q3: Manual type (Hand wheel driven) or electric motor driven type? Answer: I need type.

Q4: Screw movement (screw travelling up and down when working) or Nut movement (the nut travelling up and down when working)? Upright or Inverted? Answer: I need (A B E F)

Q5: Screw jacks linkage
Do you need 2 or above 2 sets screw jacks to linkage, if yes pls see the below screw jacks linkage scheme, if no pls ignore this.
Answer: 1. No need 2. Need, sets (2 /3 /4 /8 or other sets) screw jacks to linkage, ( I /T / L / H / U) )type ( Or you can mark it out on the below screw jacks linkage scheme picture).

For example, a 4-sets linkage H type ( without screw in this picture) as followIing:

After we got your answers we can make a CAD format drawing for you to check and quote you the best price.

Screw Jacks’ Application
Screw jak is applied to all fields for lifting or pulling, such as Aircraft maintenance platform, Solar plate, machinery, Tractor parts agriculture PTO drive cardan shaft metallurgy, water conservancy, medical treatment, chemical industry, culture and hygienist etc.

Packaging & Shipping
Packaging Details:
Polythene liner bag enclosing screw jack (which is moisture barrier, rust-proof).
Polyurethane foam around the screw jack (avoiding shock in delivery) in veneer case.

Company Information
Lude Transmission is concentrated on speed reduction and transmission industry and specialized in manufacturing screw jack, slewing drive. Our company enjoys high-end CNC machining center and professional technology development team.

Why choosing us?

(1) We have first-class testing equipment to detect bearing various data parameters and control the quality of the bearing.

Whenever bearings must first detected whether the quality is qualified and the unqualified bearing will be eliminated directly.

So we can get the trust of a large customer, and supply them for several years.
(2) We have our own R & D capabilities, to help customers solve the problem of non-standard bearings.

We can also according to customer requirements change their own mark.
(3) price, Truck gearbox accessories auto transmission synchronizer assembly our manufacture ensure that our prices across China are quite competitive.

FAQ

How to Choose the Right Worm Shaft

You might be curious to know how to choose the right Worm Shaft. In this article, you will learn about worm modules with the same pitch diameter, Double-thread worm gears, and Self-locking worm drive. Once you have chosen the proper Worm Shaft, you will find it easier to use the equipment in your home. There are many advantages to selecting the right Worm Shaft. Read on to learn more.
worm shaft

Concave shape

The concave shape of a worm’s shaft is an important characteristic for the design of a worm gearing. Worm gearings can be found in a wide range of shapes, and the basic profile parameters are available in professional and firm literature. These parameters are used in geometry calculations, and a selection of the right worm gearing for a particular application can be based on these requirements.
The thread profile of a worm is defined by the tangent to the axis of its main cylinder. The teeth are shaped in a straight line with a slightly concave shape along the sides. It resembles a helical gear, and the profile of the worm itself is straight. This type of gearing is often used when the number of teeth is greater than a certain limit.
The geometry of a worm gear depends on the type and manufacturer. In the earliest days, worms were made similar to simple screw threads, and could be chased on a lathe. During this time, the worm was often made with straight-sided tools to produce threads in the acme plane. Later, grinding techniques improved the thread finish and reduced distortions resulting from hardening.
When a worm gearing has multiple teeth, the pitch angle is a key parameter. A greater pitch angle increases efficiency. If you want to increase the pitch angle without increasing the number of teeth, you can replace a worm pair with a different number of thread starts. The helix angle must increase while the center distance remains constant. A higher pitch angle, however, is almost never used for power transmissions.
The minimum number of gear teeth depends on the angle of pressure at zero gearing correction. The diameter of the worm is d1, and is based on a known module value, mx or mn. Generally, larger values of m are assigned to larger modules. And a smaller number of teeth is called a low pitch angle. In case of a low pitch angle, spiral gearing is used. The pitch angle of the worm gear is smaller than 10 degrees.
worm shaft

Multiple-thread worms

Multi-thread worms can be divided into sets of one, two, or four threads. The ratio is determined by the number of threads on each set and the number of teeth on the apparatus. The most common worm thread counts are 1,2,4, and 6. To find out how many threads you have, count the start and end of each thread and divide by two. Using this method, you will get the correct thread count every time.
The tangent plane of a worm’s pitch profile changes as the worm moves lengthwise along the thread. The lead angle is greatest at the throat, and decreases on both sides. The curvature radius r” varies proportionally with the worm’s radius, or pitch angle at the considered point. Hence, the worm leads angle, r, is increased with decreased inclination and decreases with increasing inclination.
Multi-thread worms are characterized by a constant leverage between the gear surface and the worm threads. The ratio of worm-tooth surfaces to the worm’s length varies, which enables the wormgear to be adjusted in the same direction. To optimize the gear contact between the worm and gear, the tangent relationship between the two surfaces is optimal.
The efficiency of worm gear drives is largely dependent on the helix angle of the worm. Multiple thread worms can improve the efficiency of the worm gear drive by as much as 25 to 50% compared to single-thread worms. Worm gears are made of bronze, which reduces friction and heat on the worm’s teeth. A specialized machine can cut the worm gears for maximum efficiency.

Double-thread worm gears

In many different applications, worm gears are used to drive a worm wheel. These gears are unique in that the worm cannot be reversed by the power applied to the worm wheel. Because of their self-locking properties, they can be used to prevent reversing motion, although this is not a dependable function. Applications for worm gears include hoisting equipment, elevators, chain blocks, fishing reels, and automotive power steering. Because of their compact size, these gears are often used in applications with limited space.
Worm sets typically exhibit more wear than other types of gears, and this means that they require more limited contact patterns in new parts. Worm wheel teeth are concave, making it difficult to measure tooth thickness with pins, balls, and gear tooth calipers. To measure tooth thickness, however, you can measure backlash, a measurement of the spacing between teeth in a gear. Backlash can vary from one worm gear to another, so it is important to check the backlash at several points. If the backlash is different in two places, this indicates that the teeth may have different spacing.
Single-thread worm gears provide high speed reduction but lower efficiency. A multi-thread worm gear can provide high efficiency and high speed, but this comes with a trade-off in terms of horsepower. However, there are many other applications for worm gears. In addition to heavy-duty applications, they are often used in light-duty gearboxes for a variety of functions. When used in conjunction with double-thread worms, they allow for a substantial speed reduction in one step.
Stainless-steel worm gears can be used in damp environments. The worm gear is not susceptible to rust and is ideal for wet and damp environments. The worm wheel’s smooth surfaces make cleaning them easy. However, they do require lubricants. The most common lubricant for worm gears is mineral oil. This lubricant is designed to protect the worm drive.
worm shaft

Self-locking worm drive

A self-locking worm drive prevents the platform from moving backward when the motor stops. A dynamic self-locking worm drive is also possible but does not include a holding brake. This type of self-locking worm drive is not susceptible to vibrations, but may rattle if released. In addition, it may require an additional brake to keep the platform from moving. A positive brake may be necessary for safety.
A self-locking worm drive does not allow for the interchangeability of the driven and driving gears. This is unlike spur gear trains that allow both to interchange positions. In a self-locking worm drive, the driving gear is always engaged and the driven gear remains stationary. The drive mechanism locks automatically when the worm is operated in the wrong manner. Several sources of information on self-locking worm gears include the Machinery’s Handbook.
A self-locking worm drive is not difficult to build and has a great mechanical advantage. In fact, the output of a self-locking worm drive cannot be backdriven by the input shaft. DIYers can build a self-locking worm drive by modifying threaded rods and off-the-shelf gears. However, it is easier to make a ratchet and pawl mechanism, and is significantly less expensive. However, it is important to understand that you can only drive one worm at a time.
Another advantage of a self-locking worm drive is the fact that it is not possible to interchange the input and output shafts. This is a major benefit of using such a mechanism, as you can achieve high gear reduction without increasing the size of the gear box. If you’re thinking about buying a self-locking worm gear for a specific application, consider the following tips to make the right choice.
An enveloping worm gear set is best for applications requiring high accuracy and efficiency, and minimum backlash. Its teeth are shaped differently, and the worm’s threads are modified to increase surface contact. They are more expensive to manufacture than their single-start counterparts, but this type is best for applications where accuracy is crucial. The worm drive is also a great option for heavy trucks because of their large size and high-torque capacity.

China manufacturer Low cost Manual lifting screw jacks with hand wheel  near me supplier China manufacturer Low cost Manual lifting screw jacks with hand wheel  near me supplier